thermal softening
英 [ˈθɜːml ˈsɒfnɪŋ]
美 [ˈθɜːrml ˈsɔːfnɪŋ]
网络 热软化
双语例句
- Thermal Deformation and Vicat Softening Temperature Tester Based on Neural Network PID Temperature Control
基于神经网络PID温度控制的热变形与维卡软化温度测定仪 - The results showed that both methods of air blowing and thermal polycondensation in the presence of nitrogen raised the asphalt softening points, and increased coke yields and heptane insolubles.
结果表明，空气氧化和氮气热缩聚可提高石油沥青的软化点、焦产率和正庚烷不溶物含量。 - So far as the high refracto-riness, the high thermal stability and the high softening point under load of the magnesia spinel brick are concerned, it is possible to prepare them either by using highly purified raw materials or by adding chromite.
直接结合镁铝砖具有高耐火、高热稳和高荷重软化的性能，它可以由纯原料或用添加氧化铬矿物来制备。 - Alumina dispersion strengthened copper composite ( Al_2O_3/ Cu composite) is an attractive engineering material for applications requiring high strength, high thermal and electrical conductivities and resistance to softening at elevated temperatures.
Al2O3弥散强化铜基复合材料（Al2O3/Cu复合材料）因其具有优良的高强度高导电性能以及抗高温软化性能而成为备受瞩目的一种工程材料。 - Thermal softening of rattan canes: influence of the hemi cellulose-lignin matrix
棕榈藤的热软化：半纤维木素基质的影响 - A corresponding computer program by using finite element methed is coded in FORTRAN 77 and is implemented on microcomputers. Numerical results show that the thermal stress and material softening irradiated laser beam will induce the catastrophic buckling failure of the pre compressed cylindrical shell.
数值计算结果表明，激光照射区域产生的热应力和材料软化将导致处于正常工作状态的轴压圆柱壳发生灾难性的热屈曲破坏。 - Numerical analysis indicates that strain hardening and strain rate hardening are to resist the growth of voids, whereas the ambient temperature is to promote the growth of voids in OFHC. It is also shown that the thermal softening has negligible influence on the growth of voids.
模型的数值分析表明，对OFHC铜来说，应变硬化效应、应变率效应阻碍了孔洞的增长，热效应对孔洞增长影响不大，而环境温度的升高促进了孔洞的增长。 - In model 2, the material parameters are independent of the plastic volumetric strain but is related to the temperature change that causes thermal softening, the model is used inside the fault zone.
模型2用来模拟断层物质，其强度只同热状态有关而与塑性变形无关。 - The testing involved Comprehensive thermal analysis loading softening performance.
测定内容包括对南钢烧结矿试样的综合热分析和烧结矿荷重软化性能的测定。 - Hardness measurement on welding thermal simulated specimens and cross weld specimens showed that no softening occurred in the HAZ. All the cross weld tensile specimens ruptured in the base metal.
无论是焊接热模拟试件还是焊接接头硬度测试均表明HAZ不存在软化问题，接头拉伸试验断在远离热影响区的母材上。 - For the eight species, variation in the degree of thermal softening was observed.
8种品种的热软化程度差异也被观测到。 - A thermal postbuckling analysis is presented for a rectangular plate subjected to uniform and nonuniform ( parabolic) temperature loading and resting on a "softening" nonlinear elastic foundation.
给出非线性弹性基础上矩形板在均匀和非均匀（抛物型）热分布作用下的后屈曲分析。 - The thermal stability and Vicat softening temperature of blends rise at certain degree also.
此外，共混物的热稳定性和维卡软化点温度也有一定程度的提高。 - Experiments on cube strengths bend strength thermal conductivity, coefficient of softening mechanical and physical performance index etc are carried out. The mix proportion of polystyrene concrete we find out can meet the needs of building system.
根据得到的配合比，对EPS轻集料混凝土进行了抗压强度、抗折强度、导热系数、软化系数等力学物理性能试验，试验结果表明，该混凝土的各项指标能达到建筑体系的要求。 - The thermal characteristics of toner were introduced. The relations of toner composition with glass transition temperature, softening temperature and melting index were investigated. The glass transition temperature of polymerization toner were tested, and compared with calculational value.
介绍了墨粉的热学特性，考察了墨粉的玻璃化转变温度、软化点、熔融指数与墨粉组成的关系，测试了聚合型墨粉的温度特性并与理论计算进行对比。 - Thermal and mechanical response of the internally pressured cylindrical shell under laser irradiation is analyzed by FEM/ Explicit, and the dynamic failure phenomenon, including thermal softening, ablation and bursting, are simulated.
采用动力有限元显式积分程序，对承受内压、在侧面受到激光辐照的圆柱壳的热力学响应进行了数值模拟，展现了圆柱壳热软化、鼓包和爆裂的动态失效过程。 - Applications of Differential Thermal Analysis on Determination Softening Point and Acid Value of Rosin
差热分析在测定松香软化点、酸值研究上的应用 - It is found that particle and substrate preheating can promote the occurrence of thermal softening effect, and then enhance the plastic deformation and final bonding strength between particles and substrate.
研究结果表明，预热处理可以促进粒子或基体发生热软化效应，进而促进强塑性变形的发生，同时提高接触面附近的局部温度，促进粒子与基体的结合。 - To the physical properties, CNTs/ Al composite gains the advantages over pure aluminum in density, coefficient of thermal expansion and resistive softening temperature, but too high content of CNTs will negatively affect the tightness and high temperature stability of the composite.
物理性能方面，与纯铝相比，CNTs原位增强铝基复合材料在密度、热膨胀系数、抗软化温度方面具有明显优势，但过高的CNTs含量对复合材料致密度、高温稳定性有不利影响。 - It is found that the fluctuation is induced by the gradual aggravation of thermal expansion and thermal softening, and is closely related to the evolution of plastic zone in the metal material.
根据激光静态加热过程中应力出现的波动现象，发现是热膨胀、热软化逐渐加剧导致的，且与金属板内部塑性区域的发展演化密切相关。 - Al2O3/ Cu composite has recently made their debut as potentially viable and attractive engineering materials for industrial applications that require high strength, high thermal-and electrical-conductivity, and high resistance to softening at elevated temperatures.
Al2O3/Cu复合材料因具有优良的高强度高导电性能以及抗高温软化性能而成为备受瞩目的一种工程材料。 - Metal thermal softening and thermal conductivity offset each other at a certain extent, thus adiabatic shear occurs at low cutting speeds; At high cutting speed, metal thermal softening dominates.
在中低切削速度下，金属热软化作用和热导率变化作用在一定程度上相互抵消，绝热剪切作用占主导地位；高切削速度时，金属热软化作用占主导地位。 - The paper come from the thermal properties of bleached shellac and find drying ways within its softening temprature.
本实验从漂白紫胶的热性质出发，在其软化程范围内寻找适宜的方法对其进行干燥。 - It shows obvious regularity that saw-toothed chips form as alternating effect of thermal softening and strain hardening, or periodic alternating cracks formation.
由于热软化、应变硬化的交替作用或周期性裂纹的产生，使得锯齿形切屑形成呈现很明显的规律性。 - In the current model of cutting force, Oxley model is the one which considers the material properties comprehensive mostly. However, the material strain rate effects and thermal softening effects are still considered less than.
目前所得到的切削力模型中，Oxley模型相对来说是考虑材料性能最全面的，但是对于材料的应变速率效应及热软化效应考虑不足。 - The reason for the sawtooth chips is that the adiabatic shear localization occurs in the primary deformation zones when thermal softening exceeds strain and strain rate hardening.
锯齿形切屑产生的原因是第一变形区内因热软化超过应变和应变率强化而发生了绝热剪切局部化。